GEMSC or GEMNCO 1-24 Annex 1 Practice Exam

These questions are part of the practice quiz. Start practicing

• Which two web resources provide the status of requisitioned parts?
• Which document would you reference to locate Marine Corps maintenance and readiness information?
• What is defined as the physical performance of maintenance actions?
• In gear terminology, what is the pitch circle?
• In a TAMCN table, which section is used to identify major end items?
• Which of the following steps is not part of a systematic troubleshooting approach?
• What term is defined as the calendar date specified by the requisitioner when material is required?
• Using Ohm's law, if a circuit has a supply of 120 V and a resistance of 24 Ω, what is the current drawn by the circuit?
• Which document number outlines criteria to establish a DSI/PEB per the maintenance context?
• Who is authorized to approve F/AD 1?
• Which description best defines grounding in electrical systems?
• What is the primary function of a heat sink in electronic assemblies?
• In hydraulic/pneumatic systems, which parameter primarily determines the flow rate through an orifice?
• Which option is NOT a typical step in a preventive maintenance program?
• Which publication establishes Marine Corps property accountability policy?
• Which arc-flash boundary designation is the most restrictive for personnel?
• In a basic 3/2 pneumatic valve circuit, what happens when the valve is activated?
• Which document is used to report shortages and authorized excess items in SASSY?
• Why is proper soldering technique important for electronics reliability?
• What description best characterizes items on the MCBul 3000?
• What is the maximum maintenance cycle time for a secondary repairable item inducted at an OCONUS unit?
• Which type of maintenance consists of all maintenance actions performed as result of a failure to restore equipment to an operational condition?
• UMMIPS helps to do what?
• A maintenance shop has deadlined four out of eight MRC-148s owned by Bravo Company. The company needs a total of five in order to meet mission for the next field exercise. Select a course of action that can be taken.
• Which SAC level is principal end items of high importance within SAC categories?
• What does UMMIPS use to determine priority?
• Which statement best describes the items listed on the Marine Corps Bulletin 3000?
• What does the acronym TFSMS stand for?
• Which of the following describes unilateral tolerances?
• In 5S, what does Sustain focus on?
• Which report shows active service requests by section for maintenance managers?
• PMCS stands for which phrase?
• Why is lubrication essential for bearings in rotating machinery?
• A unit may be authorized up to how many months for a policy waiver on MC maintenance/supply policy deviations?
• Which acronym denotes the mechanism used to associate another service request from another echelon or commodity to your own service request?
• Which codes are assigned to HQMC and identify echelons authorized to repair equipment?
• What is the correct order of a systematic approach to troubleshooting a malfunctioning electrical system?
• What is the primary reason to remove or isolate flammable materials before welding?
• What is EMI and why is it a concern?
• Two systems of the FLIS that are used to gather technical data are (BLANK)
• The mission statement is part of which source document?
• To whom should a commander submit a written request for deviations from MC maintenance/supply policy?
• What is the first step in a lockout/tagout procedure before maintenance on powered equipment?
• What is the difference between qualitative and quantitative data in maintenance reporting?
• Thrust bearings are designed to support which type of load?
• What is the purpose of the Marine Corps maintenance publications?
• What is the term used to categorize the readiness status of equipment for issue?
• Why is consulting service manuals and bulletins before repair important?
• Which device is commonly used to monitor electrical signals and determine timing characteristics such as voltage, frequency, and duty cycle?
• What is the consequence of failing to perform a Lockout/Tagout procedure before maintenance?
• On the MAL, on-hand quantity plus due-in quantity must equal which requirement?
• Which statement accurately describes the difference between alternating current (AC) and direct current (DC)?
• What is the difference between calibration and verification of instruments?
• What is the purpose of proper material handling and storage in maintenance?
• Auditors would reference which publication to understand Marine Corps property accountability policy?
• Given a feature control frame indicating a diameter tolerance of 0.05 with datums A, B, and C, what does this specify?
• An MMSOP should not be a reproduction of orders and directives but instead provide local procedures within those guidelines.
• Which source document lists allowances set by HQMC for personnel and equipment?
• In a basic 3/2 pneumatic valve circuit, when activated, which port is vented?
• What is the fundamental difference between analog and digital signals?
• Why is revision control important for service manuals and drawings?
• Which section of the TAMCN table identifies it as a major end item?
• MCO 4790.2 outlines the requirements for a unit's DSI/PEB. What document outlines criteria to establish a DSI/PEB?
• In GD&T, what is a datum?
• During the acceptance phase of the maintenance cycle, what four checks are required to be annotated on a service request?
• What is the primary safety purpose of a fire watch during welding?
• Which individual is typically responsible for authorizing selective interchange when spare parts are insufficient?
• If a digital input is left floating, which describes its logical state?
• Which UND describes a unit that can temporarily accomplish assigned missions and tasks but with effectiveness below an acceptable level of readiness?
• Which instrument is used to view waveforms and measure voltage, frequency, and duty cycle?
• Which data source provides item information and is updated monthly for download via PIEE/FEDMALL?
• Which is the correct sequence of steps in a lockout/tagout procedure before maintenance?
• In which phase of maintenance does the equipment owner get contacted to pick up repaired equipment or shipping coordination is made?
• The Marine Corps maintenance body as a whole is broken down into what levels of maintenance?
• Which statement about bearing lubrication is true?
• Which statement correctly distinguishes radial and thrust bearings?
• What does the capacitor symbol indicate on a schematic?
• What safety controls should be observed during welding near flammable materials?
• A fuse in a circuit serves to...
• What is the purpose of a 5 Whys analysis?
• During the closeout phase, where are QC comments placed in service requests?
• (BLANK) is a tool for maintenance activities to evaluate their MPR/RRGE by; supply (S%), readiness (R%), and material readiness (MR%)
• Which PPE is essential when performing grinding operations to prevent eye injury?
• What is the difference between accuracy and precision in measurement?
• Which statement describes where acceptance information is saved on service requests per UM 4000-125?
• The physical delivery of equipment to service requests and workload based on priority is covered in which phase of maintenance?
• Which SAC level is principal end items of high importance?
• Why are pull-up and pull-down resistors used with digital inputs?
• (BLANK) refers to the integration of maintenance considerations within the systems engineering approach used in developing equipment and weapons.
• On electrical schematics, what does the resistor symbol represent?
• An MPR is used to associate another service request from another echelon or commodity to your own service request. What is the correct term?
• The datum provides a common reference for tolerances.
• What is box 10 on a DD-1348 form?
• UM 4000-125 is described as which type of reference?
• Which phase is associated with closure after maintenance work and coordination?
• Which system allows a user to search the FLIS for data on an item, is updated monthly, and is available for download via PIEE/FEDMALL?
• What does the term zero-energy state mean in lockout/tagout practice?
• What is a common method for shaft alignment to minimize misalignment?
• (BLANK) gives a user the most current data on supply items and manufacturers/suppliers
• What does the 'Qty Recv'd' field indicate on a DD-1348 form?
• In an electrical schematic, what does a fuse symbol indicate and when is it used?
• Aside from yield strength, which property is commonly cited as important for fasteners under load (as an alternative property)?
• What is the primary purpose of a lockout device in isolating energy sources?
• What is a common method for shaft alignment to minimize misalignment?
• Name a standard governing electrical safety in the workplace.
• Which document is used to track incoming and outgoing transfers from CMR?
• In a pneumatic diagram, which component regulates the rate of air flow into a cylinder for slow, smooth extension?
• What is the difference between lockout/tagout and group lockout in safety practice?
• The ESR evaluates MPR/RRGE by which three percentages?
• Which phase of maintenance covers inspection, scheduling, and assignment?
• Which of the following is used to cover where the MMSOP is vague or inadequate for units?
• Which stores account code item is described by SAC 1?
• Which of the following lists the five 5S principles?
• Select the option that corresponds to the UMMIPS order.
• In a ladder diagram, what is the role of a relay coil and its contacts?
• Which statement best describes the objective of UM 4000-125?
• What is defined as the removal of serviceable parts from one item of equipment to install them on another item of equipment without replacement?
• Which document is used to communicate the status of ongoing tasks and management controls within a unit?
• Name a material property important for fasteners under load, such as yield strength or hardness.
• Why is root-cause analysis essential in maintenance?
• Who must ensure maintenance management and maintenance receive full command support?
• Which maintenance approach focuses on changing design characteristics of equipment to improve performance and safety?
• Name the two FLIS systems used to gather technical data.
• In GD&T, a 0.05 diameter tolerance defines what type of tolerance zone?
• Which resource is used to find Marine Corps MRR/RRGE information?
• Which codes are used to provide spelled-out instructions for items submitted for WIR?
• PMCS is a maintenance category defined as which of the following activities that keep equipment in an operationally ready condition, including servicing, adjustments, and turning?
• Which reference establishes Marine Corps wide GCSS-mc equipment temp loan procedures?
• In which phase of maintenance do maintenance personnel assemble appropriate technical manuals and other technical information, support equipment, and TMDE to perform required service?
• What document lists Marine Corps MRR/RRGE?
• In a series circuit, how does adding another resistor affect current?
• Which publication outlines maintenance policies to improve staff planning and unit readiness across the Marine Corps?
• The DLA handbook primarily serves as a quick reference for what?
• PubLogFLIS provides data on which category most relevant to logistics?
• What type of sensor output is commonly compatible with a microcontroller ADC?
• Per UM 4000-125, where is the acceptance information saved on the service requests?
• RDD stands for which of the following?
• In a TAMCN table, which section identifies a TAMCN as a major end item?
• What portion of the mission statement provides the level of maintenance the unit is authorized to perform?
• In maintenance documentation, which resource typically contains concise notes about everyday tasks for a particular billet?
• Why is proper grounding and shielding important in EMI/RFI management?
• Which UND corresponds to required installation or repair of mission essential equipment without which the unit is unable to perform their assigned mission?
• What term describes the state of an asset's readiness for issue?
• (BLANK) is the maximum amount of time that should elapse during any given segment of the supply chain, from the origination of the requirement to the time of physical receipt.
• In data analysis for reliability, what is the purpose of a Pareto chart?
• Which Marine Corps order number is associated with the UMMIPS according to the provided material?
• Which office is authorized to approve F/AD 1?
• Who is required to have desktop procedures?
• What are the web resources that provide the latest information available on the status of requisitioned parts?
• What is the primary function of setting intervals in a preventive maintenance program?
• What is the main benefit of documenting maintenance results?
• The pitch circle concept is used to determine which characteristic of a gear pair?
• Which document is a simple listing of significant items or notes pertinent to everyday operations within a billet?
• Which report lists the status of service requests by section?
• In a ladder diagram, energizing a relay coil affects its normally open (NO) and normally closed (NC) contacts?
• What term describes the exchange of selected serviceable repair parts from a deadlined item for unserviceable repair parts from a like item with replacement?
• Which report serves as a maintenance requisition troubleshooting tool?
• Who is delegated the authority to assign F/ADs 2 through 5 within the Marine Corps?
• Which GD&T symbol denotes circularity (roundness)?
• Which protective device interrupts current during an overload in an electrical system?
• What are typical steps in a preventive maintenance program?
• What type of maintenance consists of those maintenance actions performed to change the design of assembly characteristics of equipment systems, end items, components, assemblies, subassemblies, or parts in order to improve equipment functioning, reliability, and/or safety characteristics?
• Which instrument is typically used to measure pressure in hydraulic systems?
• What determines who must maintain desktop procedures?
• What report is a supply responsibility that can be used as a troubleshooting tool for maintenance and maintenance management personnel to identify problems with requisitions?
• Responsible Offices (RO) must be appointed in writing by whom to assume responsibility for assets?
• If a dimension is controlled with a datum reference frame involving A, B, and C, what is its primary effect?
• (BLANK) is an enterprise system that combines manpower and data for the purpose of managing the total force.
• Which discipline focuses on including maintenance considerations within the systems engineering process when developing equipment and weapons?
• What is the primary purpose of documenting the troubleshooting process?
• What is the purpose of safe distance and barriers in electrical work?
• What is the maximum maintenance cycle time for an end item inducted at a CONUS unit?
• What document is used to maintain accountability of equipment dispersed across the command?
• What are typical electrical arc-flash boundary designations used in workplace safety standards?
• Name the document that tracks accountability for equipment spread across multiple locations within the command.
• Which document will include information about policy, personnel, status of pending projects, references, management controls, functioning of the section, ways and means of accomplishing routine as well as infrequent tasks, and information of value assigned to that billet?
• According to UM 4000-125, what is the requirement for notifying the owner that repairs are complete?
• Which source document is described as a snapshot of shortages and/or authorized excess of allowed items as reported in SASSY?